Publications
|
Journal
2024
·
Gökay G., Çetin
B. and Dursunkaya Z. “Accelerated 3D CFD modeling of multichannel flat
grooved heat pipes”, Energy, 305, 132289, 2024 https://doi.org/10.1016/j.energy.2024.132289
2023
·
Yuncu, G., Akkus, Y. and Dursunkaya, Z., “Elliptical pillars
for the thermal performance enhancement of micro-structured evaporators”, International Communications in Heat and Mass
Transfer, 148,107036, 2023, https://doi.org/10.1016/j.icheatmasstransfer.2023.107036
·
Gökay G., Odabaşı G., Kurt C., Dursunkaya Z. and Çetin B. “Comprehensive
three-dimensional hydrodynamic and thermal modeling of steady-state operation
of a flat grooved heat pipe”, International Journal of Multiphase Flow, 160, 104370,
2023 https://doi.org/10.1016/j.ijmultiphaseflow.2022.104370
·
Yuncu, G., Akkus, Y. and Dursunkaya, Z., “Interplay of
capillary and Marangoni flows in micropillar
evaporation”,
International Journal of Thermal Sciences, 184, 107893, February 2023, https://doi.org/10.1016/j.ijthermalsci.2022.107893
2022
·
Saygan S., Akkuş Y., Dursunkaya Z. and Çetin B., “Capillary boosting
for enhanced heat pipe performance through bifurcation of grooves: numerical
assessment and experimental validation”, International
Communications in Heat and Mass Transfer, 137,
106162, October 2022 https://doi.org/10.1016/j.icheatmasstransfer.2022.106162
·
Saygan S., Akkuş Y., Dursunkaya Z. and Çetin B., “Fast and
predictive heat pipe design and analysis toolbox: H-PAT”, Isi Bilim Tek. Derg.-J. Therm. Sci. Tech.,
42(1):141—156, April 2022, https://doi.org/10.47480/isibted.1107492
2021
·
Akdağ O., Akkuş Y., Çetin B. and Dursunkaya Z., “Interplay of
transport mechanisms during the evaporation of a pinned sessile water droplet”, Physical Review Fluids, 6, 073605, July 2021, https://doi.org/10.1103/PhysRevFluids.6.073605
2020
·
Rezaeimoghaddam M. and and Dursunkaya Z., “The effect of surface morphology on the rate of phase
change of micron and sub-micron sized 2-D droplets”, Nanoscale and Microscale Thermophysical Engineering, 24, 3—4, pp.184—200, 2020 https://doi.org/10.1080/15567265.2020.1853290
·
Akkuş Y., Çetin B. and
Dursunkaya Z., “A theoretical
framework for comprehensive modeling of steadily fed evaporating droplets and
the validity of common assumptions”, International
Journal of Thermal Sciences, 158,
106529, December 2020, https://doi.org/10.1016/j.ijthermalsci.2020.106529
·
Akdağ O., Akkuş Y. and Dursunkaya Z., “On the effect of structural forces on a condensing
film profile near a fin-groove corner”, International
Communications in Heat and Mass Transfer,
116, 104686, June 2020, https://doi.org/10.1016/j.icheatmasstransfer.2020.104686
2019
·
Atay A., Sarıarslan B., Kuşcu YF., Saygan S., Akkuş Y., Gürer TA., Çetin B. and Dursunkaya Z., “Performance assessment of commercial heat
pipes with sintered and grooved wicks under natural convection”, Journal of Thermal Science and Technology (IBTD), 39-2, pp.101–110, October 2019
·
Alipour M. and
Dursunkaya, Z., “Limitations of matching condensing film
profile on a micro fin with the groove: critical effect of disjoining pressure,” Nanoscale and
Microscale Thermophysical Engineering, 23, 4, pp.289—303, 2019 https://doi.org/10.1080/15567265.2019.1633712
·
Akdağ O., Akkuş Y. and Dursunkaya Z., “The effect of
disjoining pressure on the shape of condensing films in a fin-groove corner”, International Journal of Thermal Sciences, 142, pp.357—365,
August 2019 https://doi.org/10.1016/j.ijthermalsci.2019.04.008
·
Alijani H., Akkuş Y., Çetin B. and
Dursunkaya Z., “Experimental Thermal Performance
Characterization of Flat Grooved Heat Pipes”, Heat Transfer Engineering, 40 (9–10), pp. 784–793, June 2019 https://doi.org/10.1080/01457632.2018.1442395
·
Akkuş Y., Çetin B. and
Dursunkaya Z., “An iterative solution approach to coupled
heat and mass transfer in a steadily fed evaporating water droplet”, ASME Journal of Heat Transfer 141(3),
March 2019 https://doi.org/10.1115/1.4042492
2018
·
Alijani H., Akkuş Y., Çetin B. and
Dursunkaya Z., “Effect of Design and Operating Parameters on
the Thermal Performance of Aluminum Flat Grooved Heat Pipes”,
Applied Thermal Engineering, 132, pp 174—187, March 2018 https://doi.org/10.1016/j.applthermaleng.2017.12.085
2017
·
Akkuş Y., Tarman HI., Çetin B. and Dursunkaya Z., “Two-Dimensional Computational Modeling of
Thin Film Evaporation”, International Journal of Thermal Sciences, 121, pp.237—248, November 2017 https://doi.org/10.1016/j.ijthermalsci.2017.07.013
2016
·
Yıldırım, M.,
Okutucu-Özyurt, T. and Dursunkaya, Z., “A Numerical Algorithm to Determine
Straightness Error, Surface Roughness, and Waviness Measured using a Fiber
Optic Interferometer”, Optics and Laser Technology, 85, pp. 19—29, 2016 https://doi.org/10.1016/j.optlastec.2016.05.014
·
Akkuş, Y. and
Dursunkaya, Z., “A New Approach to Thin Film
Evaporation Modeling”, Int J Heat and Mass
Trans, 101, pp742—748, 2016 https://doi.org/10.1016/j.ijheatmasstransfer.2016.05.091
·
Odabaşı, G. and Dursunkaya, Z., “Modeling of Two-Dimensional Solidification of a Finite
Cylinder,” Journal of Thermal
Science and Technology (IBTD), 36-1,
pp. 61–68, April 2016
2009
·
Okman O., Dursunkaya,
Z. and Tekkaya E., “Generalized Transient Temperature Behavior in
Induction Heated Workpieces,” Journal of Materials Processing Technology, 209,
pp. 5932 – 5939, 2009 https://doi.org/10.1016/j.jmatprotec.2009.07.010
2007
·
Özgen, S.,
Dursunkaya, Z. and Ebrinç, A.A., “Heat transfer effects on the stability of
low-speed plane Couette-Poiseuille flow”, Heat and Mass Transfer, 43, pp 1317-1328, 2007 https://doi.org/10.1007/s00231-006-0208-5
2006
·
Dursunkaya, Z. and Nair, S., “Accuracy of the two-iteration spectral method for
phase change problems,” Applied Mathematical Modelling, 30, pp.1515-1524, 2006
https://doi.org/10.1016/j.apm.2005.07.006
2005
·
İçöz,
T. and Dursunkaya, Z., “Experimental Investigation of Oil Accumulation in
Second Land of Internal Combustion Engines,” ASME
Trans, J Eng for Gas Turb
and Power, 127, pp. 206-211, 2005 https://doi.org/10.1115/1.1805011
2003
·
Dursunkaya, Z. and
Odabaşı, G., “Numerical solution of solidification
in a square prism using an algebraic grid generation technique,” Heat and Mass Transfer, 40, pp 91-97, 2003
·
Dursunkaya, Z. and
Nair, S., “Solidification
of a Finite Medium Subject to a Periodic Variation of Boundary Temperature,”
ASME Trans, J Applied Mechanics, 70, pp 633-637, 2003 https://doi.org/10.1115/1.1604836
1994
·
Dursunkaya, Z., Keribar, R. and Ganapathy, V., “A Model of
Piston Secondary Motion and Elastohydrodynamic Skirt Lubrication,” ASME Trans, J Trib,
116, pp 777-785, 1994 https://doi.org/10.1115/1.2927332
1992
·
Dursunkaya, Z. and
Keribar, R., “Simulation of Secondary Dynamics of
Articulated and Conventional Piston Assemblies,” SAE Trans, J
Engines, 101, pp. 853-863, 1992 https://doi.org/10.4271/920484
·
Keribar, R. and
Dursunkaya, Z., “A Comprehensive Model of Piston Skirt Lubrication,” SAE Trans, J
Engines, 101, pp. 844-852, 1992 https://doi.org/10.4271/920483
·
Wahiduzzaman S., Keribar R., Dursunkaya, Z. and Kelly F. A., “A Model for
Evaporative Consumption of Oil in Reciprocating Engines,” SAE Trans, J Fuels
and Lubricants, 101, pp. 1192-1200,
1992 https://doi.org/10.4271/922202
·
Dursunkaya, Z. and
Worek, W. M., “Diffusion-thermo
and Thermal-diffusion Effects in Transient and Steady Natural Convection from a
Vertical Surface,” Int J Heat and Mass
Trans, 35, pp. 2060-2065,1992 https://doi.org/10.1016/0017-9310(92)90208-A
1991
·
Keribar, R., Dursunkaya,
Z. and Flemming, M.F., “An Integrated Model of Ring Pack Performance,”
ASME Trans, J Eng for Gas Turb and Power, 113, pp. 382-389, 1991 https://doi.org/10.1115/1.2906242
1990
·
Dursunkaya, Z. and
Nair, S., “A Moving Boundary Problem in a Finite
Domain,” ASME Trans, J
Applied Mechanics, 57, pp. 50-56,
1990 https://doi.org/10.1115/1.2888323
Conference
2023
·
Gökay G., Çetin
B., and Dursunkaya Z. “Accelerated Solution Methodology for 3D Hydrodynamic
and Thermal Modeling of Grooved Heat Pipes with Complex Geometries”, 14th ICCHMT, 4—8 September
2023, Düsseldorf, Germany
·
Derebaşı,
B., Saygan S., Çetin B. and
Dursunkaya Z., “Effect of Liquid-Vapor Interaction on the Thermal Performance of a Flat Grooved Heat Pipe”, 8th Thermal and Fluids Engineering Conference (TFEC), TFEC-2023-45873, May 2023, Maryland USA
·
Yuncu G., Akkus Y.
and Dursunkaya Z., “Elliptic Micropillar Wick Evaporators for Thermal Management of High Flux
Electronics”,
22nd Intersociety Conference on Thermal and Thermomechanical Phenomena in
Electronic Systems,
May 30—June 2, 2023, Orlando FL USA
2022
·
Çetin B., Gökçe G,, Kurt C., Odabaşı G. and
Dursunkaya Z., “Thermal Performance
Characterization of a Flat-Grooved
Heat Pipe Integrated Cold Plate”, Proceedings of CONV-22: Int. Symp. on Convective Heat and Mass
Transfer June 5 – 10, 2022, Turkey
DOI:10.1615/ICHMT.2022.CONV22.520
2021
·
Çetin B., Gökçe G,, Kurt C., Odabaşı G. and
Dursunkaya Z., “Three-dimensional hydrodynamic and thermal modeling of a flat grooved heatpipe using three different
formulations ”, 74th
Annual Meeting of the APS Division of Fluid Dynamics, Phoenix, Arizona USA, November
21—23, 2021
·
Dursunkaya Z., “State of The Art in Grooved
Heat Pipes: Modeling, Experimentation & Applications”, ULIBTK’21, Gaziantep, September
8—10, 2021, Keynote Speech
·
Erkan Y.B. and Dursunkaya Z., “Coalescence of Micron-Submicron
Sized Thin Films”, ULIBTK’21,
Gaziantep, September 8—10, 2021
·
Sezmen R.A., Çetin B. and Dursunkaya Z., “Performance of a flat grooved heat pipe
with a localized heat load ”, ICCHMT, Paris, France (Virtual) May 18—20, 2021
·
Saygan S., Akkuş Y., Çetin B. and Dursunkaya Z., “Experimental validation of the heat pipe
evaluation software ‘Heat Pipe
Analysis Toolbox (H-PAT)’ ”, ICCHMT,
Paris, France (Virtual) May 18—20, 2021
·
Akdağ O., Akkuş Y., Çetin B. and Dursunkaya Z., “Modeling the evaporation of drying sessile droplets with buoyancy
driven internal convection”, ICCHMT,
Paris, France (Virtual) May 18—20, 2021
·
Gökçe G., Çetin B. and Dursunkaya Z., “Dryout performance assessment of grooved heat pipes using
a 3-d computatıonal model”,
ATE-HEFAT 2021 15th International on Heat Transfer, Fluid
Mechanics and Thermodynamics,
Rotterdam Holland (Virtual), July
25—28, 2021
2019
·
Saygan S.
and Dursunkaya Z., “Design,
construction and commissioning
of a flat grooved heat pipe with
adjustable evaporator and condenser ”,
ULIBTK’19, İzmit, September 11—14, 2019
·
Gökçe G. and Dursunkaya Z., “Thermal Performance
Evaluation Methodology of Grooved
Heat Pipes With Rectangular, Trapezoidal and Wedge Cross Sections”, 16th UK Heat Transfer Conference (UKHTC2019-224)
Nottingham UK, September 8—10, 2019
·
Akdağ O., Akkuş Y. and Dursunkaya Z., “Disjoining
Pressure Instigated Slope Break of a Condensing Film in a Fin-Groove Corner”, ICCHMT, Rome, Italy, September 3—6, 2019
·
Gökçe G., Altunkaş
O., Çetin B. and Dursunkaya Z., “Comparison of 1-D and
3-D Modeling Methodologies for Flat-Grooved Heat Pipes”, ICCHMT, Rome,
Italy, September 3—6, 2019
2018
·
Jafari-Tabrizi., A. and Dursunkaya, Z., “An interferometric
apparatus for the measurement of oil film thickness in a journal bearing”, 2018 STLE Tribology Frontiers Conference (Co-sponsored
by ASME Tribology Division) Chicago IL, USA, October
28—31, 2018
·
Alipour M., and Dursunkaya, Z., “The effect of disjoining pressure on the condensing film in a flat grooved heat
pipe”, Joint 19th IHPC and 13th IHPS, Pisa,
Italy, June 10—14, 2018
·
Kurt, C., Alijani,
H., Çetin, B. Akkuş,Y. and Dursunkaya, Z., “Experimental Investigation of
Thermal Performance of a Silicon
Flat Plate Grooved Heat Pipe with an Integrated Heater and Cooler”, ASME
2018 ICNMM, Dubrovnik Croatia,
June 10—13, 2018
2017
·
Akkuş Y., Çetin B. and Dursunkaya Z., “Investigation of evaporation from a sessile constant shape droplet”, ASME 2017 ICNMM, Cambridge MA,
USA, August 27—31 2017
·
Alijanvad,
H., Çetin, B. Akkuş,Y. and
Dursunkaya, Z., “Experimental Investigation of
Thermal Performance of an Aluminum
Flat-Grooved Heat Pipe”, ASME
2017 ICNMM, Cambridge MA, USA, August 27—31 2017
·
Akdağ O., Akkuş Y. and Dursunkaya Z., “A model of liquid flow on the condensation
fin top-groove corner of a micro-grooved heat pipe”, ICCHM2T, Seoul, Korea, May 28-June1 2017
·
Alijanvad,
H., Çetin, B. Akkuş,Y. and
Dursunkaya, Z., “3D modeling of a micro-grooved heat pipe”, ICCHM2T, Seoul, Korea, May 28-June1 2017
·
Alipour M., and Dursunkaya, Z., “Condensation modeling on the fin top of a micro-grooved heat pipe”, 26th Canadian Congress of Applied Mechanics Victoria BC, Canada, May 29-June 1 2017
2016
·
Alijanvad,
H., Çetin, B. and Dursunkaya, Z., “Experimental Investigation of
Thermal Performance of an Aluminum-Grooved
Micro Heat Pipe”, 5th Micro and Nano Flows Conference Milan, Italy, 11-14 September 2016
·
Akkuş Y, and Dursunkaya Z., “Thin Film Evaporation
in Grooved Heat Pipes”, 2016 International Conference of Microfluidics,
Nanofluidics and Lan-on-a-Chip,
June 10–12, 2016 Dalian China
·
Açık S.,
Dursunkaya Z. and Toker A., “Internal Ballistic Design Optimization of
Solid Rocket Motors with Direct Search Method ”
Space Propulsion
2016, 2–6 May, 2016 Rome, Italy (SP2016_ 3125080)
·
Baloğlu E.C., Okutucu-Özyurt T. and Dursunkaya, Z., “Investigation of Warpage Behavior of Single Crystal Silicon on a Silicon – Adhesive – Ceramic Integrated Structure at Cryogenic Temperatures”,
IMAPS, 12th International Conference and Exhibition
on Device Packaging, 15–17 March
2016, Arizona USA
2015
·
Yücel, O., Açık, S., Toker, K.A.,
Dursunkaya, Z. and Aksel, M.H., “Three-Dimensional Grain Design Optimization
of Solid Rocket Motors”, 7th
International Conference on Space Technologies, June 16–19, 2015, İstanbul, Turkey
·
Taze, S., Çetin, B., and
Dursunkaya, Z., “Multi-Physics Modeling of
Silicon-Based Micro-Grooved Heat Pipe,” 8th International Conference on Computational Heat and Mass
Transfer, May 25–28, 2015, İstanbul,
Turkey
2010
·
Yıldırım, M., Dursunkaya, Z. and
Okutucu T., “An Interferometric Technique
for Measuring Micron Level Clearances Filled with a Lubricant,” STLE/ASME International Joint
Tribology Conference, IJTC2010, October 17-20, 2010, San Francisco, California,
USA
·
Hacıoğlu, B. and Dursunkaya, Z., “Effect of Surface Texture on Compressor Piston
Lubrication,” Proceedings of the International Compressor Engineering Conference at Purdue,
July 12-15, 2010, West Lafayette Indiana, USA
2009
·
Yıldırım, M., Dursunkaya, Z. and
Okutucu T., “Experimental Investigation
Micron Level Clearances Using Fiber Optic Interferometry,” 11th International Conference on Tribology, May 13-15, 2009,
Belgrade, Serbia
2008
·
Hacıoğlu, B. and Dursunkaya, Z., “Effect of Oil Feed Groove on Compressor Piston
Lubrication,” Proceedings of the 19th International Compressor Engineering
Conference at Purdue, July 14-17, 2008 West Lafayette Indiana, USA
2006
·
Ebrinç, A.A., Özgen, S. and Dursunkaya, Z., “High Speed
Couette—Poiseuille Flow Stability in Reverse Flow Conditions” Proceedings of 4th IASME/WSEAS International
Conference on Fluid
Mechanics and Aerodynamics, August 21-23, 2006,
Crete, Greece, pp. 215-220
·
Duyar, M. and Dursunkaya, Z., “Design Improvement Based on Wear of a Compressor Bearing Using an Elastohydrodynamic Lubrication Model,” International Compressor Engineering Conference at Purdue, Paper C058, July 17-20,
2006 West Lafayette Indiana, USA
2005
·
Özgen,
S., Dursunkaya, Z. and Ebrinç,
A.A., “Heat Transfer
Effects on the Stability of Low-speed Couette—Poiseuille Flow,” 3rd
Ankara International Aerospace Conference, August 22-25, 2005, Ankara, Turkey
·
Ebrinç, A.A., Dursunkaya, Z. and Özgen, S., “High Speed
Viscous Plane Couette—Poiseuille Flow Stability,” 3rd Ankara International Aerospace Conference, August
22-25, 2005, Ankara, Turkey
2002
·
Duyar, M. and Dursunkaya, Z., “Design Improvement of a Compressor Bearing Using an Elastohydrodynamic Lubrication Model,” International Compressor Engineering Conference at Purdue, July 16-19, West Lafayette
Indiana, USA, 2002
2000
·
Dursunkaya, Z., “Oil Loss Mechanisms due
to In-cylinder Components,” Proceedings of the International Conference on Automotive Technology,
ICAT 2000, October 19-20, Istanbul, Turkey, pp. 137-140, 2000
·
Dursunkaya, Z. and Üçtug, Y., “Preparing students for the international environment of 21st century
in Middle East Technical University,” Proceedings of the International Millenial Conference on
Engineering Education, January 27-29 Manila, Philippines, pp. 137-140, 2000
1999
·
Dursunkaya, Z., “Analysis of Piston Slap Using an Elastohydrodynamic
Piston Lubrication Model,” Proceedings of the International
Conference on Lubrication Techniques, October 27-28, Istanbul, Turkey, pp.
190-195, 1999
1993
·
Dursunkaya, Z., Keribar, R. and Ganapathy, V., “A Model of Piston
Secondary Motion and Elastohydrodynamic Skirt
Lubrication,” ASME Energy Sources and Technology Conference and Exhibition January
31-February 4, Houston Texas USA, 93-ICE-7, 1993
·
Dursunkaya, Z., Keribar, R. and Richardson, D.
E., “Experimental and Numerical Investigation of Ring Dynamics and Blowby in a Diesel Engine,” SAE International Congress
and Exhibition March 1-5, Detroit Michigan USA, SAE Paper 93792, 1993
·
Keribar, R., Dursunkaya, Z. and Ganapathy, V., “An Integrated Design
Analysis Methodology to Address Piston Tribological
Issues,” SAE International Congress
and Exhibition March 1-5, Detroit Michigan USA, SAE Paper 93793, 1993
1991
·
Keribar, R. and Dursunkaya, Z., “Modeling of Piston Secondary Dynamics and Tribology,” Proceedings of the Annual Automotive Technology Development Contractors'
Coordination Meeting, Dearborn, Michigan pp. 657-677, 1991
1990
·
Keribar, R., Dursunkaya, Z. and Flemming, M.F., “Integrated
Modeling of Ring Pack Performance,” Proceedings of the Annual Automotive Technology Development Contractors'
Meeting, Dearborn, Michigan pp. 353-366,
1990
·
Keribar, R., Dursunkaya, Z. and Flemming, M.F., “An Integrated Model of
Ring Pack Performance,” in “New Technology in Internal Combustion Engines” ICE-Vol. 13,
pp.103-112, 12th Annual Fall Technical Conference of the ASME Internal
Combustion Engine Division, Rockford IL, October 7-10, 1990
Journal (Turkish)
2008
·
Aykan,
F.S. ve Dursunkaya,
Z., “İki Boyutlu Dış Yüzeylerde
Isıl Aşınma Sayısal Analizi,” Isı Bilimi ve Tekniği Dergisi,
28, pp. 43 – 49, 2008
2001
·
Ögel, Z. ve
Dursunkaya, Z., “Eğitimde Kalite
Yönetimine Bir Örnek: ABET 2000 Akreditasyon Süreci,” Hacettepe Üniversitesi Egitim Fakültesi Dergisi, 20, pp.
206-214, 2001
Conference
(Turkish)
2021
·
Balyalıgil
G, Yücel A, Gözükara AC, Ocak M, Dursunkaya Z ve Çetin B, “Düz Oluklu Isı Borusu Entegre Soğutma
Plakasının Isıl Performansının Deneysel Olarak İncelenmesi”, ULIBTK’21, Gaziantep, 8—10 Eylül 2021
·
Ağartan Y.A. ve Dursunkaya Z., “İnce Sıvı Filmlerin ve Damlacıkların
Yüzeylerinin Fiber Optik Girişimölçer İle Ölçümü İçin Özgün Bir Yöntem
Geliştirilmesi”, 23.
Uluslararası Katılımlı Isı Bilimi ve Tekniği
Kongresi, Gaziantep, 8—10
Eylül
2021
·
Sezmen A., Çetin B. ve Dursunkaya Z., “Çok Kanallı Düz Oluklu Isı Borularının Isıl
Performans Analizi”, 23.
Uluslararası Katılımlı Isı Bilimi ve Tekniği
Kongresi, Gaziantep, 8—10
Eylül
2021
·
Saygan S., Akkuş Y., Çetin B. ve Dursunkaya Z., “Isı Borusu Analiz Aracı (H-PAT) ile Ticari
Isı Borularının Benzetimlenmesi”, 23. Uluslararası Katılımlı Isı Bilimi ve Tekniği Kongresi, Gaziantep, 8—10 Eylül
2021
·
Gökçe, G., Çetin B. ve Dursunkaya Z., “Oluklu Isı Borularında Kuru Çalışma
Rejiminin 3-Boyutlu Bir Model İle İncelenmesi
”,
23. Uluslararası Katılımlı Isı Bilimi
ve Tekniği Kongresi, Gaziantep, 8—10 Eylül
2021
·
Akdağ O., Akkuş Y., Çetin B. ve Dursunkaya Z.,
“Kaldırma Kuvvetinin Tetiklediği Taşınım İle
Kuruyan Damlacıklarda Deegan Akışının Başlangıcı”, 23. Uluslararası Katılımlı Isı Bilimi ve Tekniği Kongresi, Gaziantep, 8—10 Eylül
2021
2019
·
Gökçe, G. ve Dursunkaya Z., “Ticari HAD Programının İteratif
Kullanımıyla Faz Değişimi Modellenmesi ve Dikdörtgen Kesitli Oluklu Bir Isı
Borusunun Isıl Performansının Belirlenmesi”, 22. Ulusal Isı Bilimi ve Tekniği Kongresi, İzmit, 11—14 Eylül 2019
·
Akdağ O., Akkuş Y. ve Dursunkaya Z., “Kanatçık-Kanal Sistemindeki Ayrılma Basıncı-Yoğuşma İlişkisinin Boyutsuz Parametrelerle İncelenmesi”, 22. Ulusal Isı Bilimi ve Tekniği Kongresi, İzmit,
11—14 Eylül 2019
·
Akkuş Y., Çetin B. ve Dursunkaya Z., “Damlacık Buharlaşması Sırasında Gerçekleşen
Eşzamanlı Fiziksel Mekanizmaların Yinelemeli Çözümü”, 22. Ulusal Isı Bilimi ve Tekniği Kongresi, İzmit,
11—14 Eylül 2019
2018
·
Dursunkaya Z., “Oluklu
Isı Borularındaki Akışkanlar Mekaniği ve Isı Transferinin Fiziği”, 2018 Symposium on Advances in Thermal & Fluid
Sciences, İzmir Yüksek Teknoloji Enstitüsü, İzmir 28—29 Haziran 2018
2017
·
Harmancı B. ve Dursunkaya Z., “Mikro – Kanallı Isı Borusunun Yoğuşma
Bölgesinin Kütle Korunumlu Modellenmesi”, 21. Ulusal Isı Bilimi ve Tekniği Kongresi, Çorum,
13—16 Eylül 2017
·
Alijani H., Akkuş Y., Çetin B. ve Dursunkaya Z., “Düz-Oluklu Alüminyum Isı Borularının Isıl
Performanslarının Deneysel Olarak İncelenmesi”, 21. Ulusal Isı Bilimi ve Tekniği Kongresi, Çorum, 13—16 Eylül 2017
·
Atay A., Sarıarslan
B., Kuşcu Y., Akkuş Y., Saygan
S., Gürer T., Çetin B. ve Dursunkaya Z., “Sinterli ve Oluklu Isı Borularının Kuruma Sınırlarının
Deneysel Tespiti”, 21. Ulusal Isı Bilimi ve Tekniği Kongresi, Çorum,
13—16 Eylül 2017
·
Akdağ O., Akkuş Y. ve Dursunkaya Z., “Dışbükey Bir
Köşedeki Sıvı Film Akışının Modellenmesi”,
21. Ulusal Isı Bilimi ve Tekniği Kongresi, Çorum, 13—16 Eylül 2017
2015
·
Odabaşı, G. ve Dursunkaya Z., “Dikdörtgen Kesitli Isı Borusu İçin Üç
Boyutlu Isı Transfer Analizi,” 20.
Ulusal Isı Bilimi ve Tekniği Kongresi, Balıkesir, 2—5 Eylül 2015
·
Akkuş, Y. ve Dursunkaya Z., “Mikro Kanalli Isi Borularindaki Buharlaşma
Modellerinin İncelenmesi ve Yeni Bir Çözüm İşlemi Önerisi,” 20. Ulusal Isı Bilimi ve Tekniği Kongresi, Balıkesir,
2—5 Eylül 2015
·
Taze, S., Çetin, B., Yılmaz, M. ve Dursunkaya,
Z., “Mikro-Oluklu Isı Borusu Üretimi İçin Farklı
Mikro-Üretim Yöntemlerinin İrdelenmesi,” 20. Ulusal Isı Bilimi ve Tekniği Kongresi, Balıkesir, 2—5Eylül 2015
·
Baloğlu, E.C., , Okutucu-Özyurt, T. ve Dursunkaya, Z., “Mikroelektronik Aygıtların Düşük Sıcaklıkta Şekil
Değiştirmelerinin İncelenmesi,” 20.
Ulusal Isı Bilimi ve Tekniği Kongresi, Balıkesir, 2—5 Eylül 2015
2013
·
Bilge, E. ve Dursunkaya, Z., “İçten Yanmalı Motorlardaki Gaz Geri Akışıyla
Yağ Kaybının İncelenmesi,” 19.
Ulusal Isı Bilimi ve Tekniği Kongresi, Samsun, 9—12 Eylül 2013
2007
·
Aykan, F.S. ve Dursunkaya, Z., “İki Boyutlu Dış Yüzeylerde Isıl Aşınma
Analizi,” 16. Ulusal Isı Bilimi ve Tekniği
Kongresi, Kayseri, 30 Mayıs—2 Haziran 2007
2005
·
Özgen, S.,
Ebrinç, A.A. ve
Dursunkaya, Z., “Isı Transferinin Couette-Poiseuille
Akışının Kararlılığına Etkisi”, 15.
Ulusal Isı Bilimi ve Tekniği Kongresi, Trabzon, 7—9 Eylül 2005
2003
·
Dursunkaya, Z., “ABET 2000 Süreci:
Birimin Özgörevi Doğrultusunda Eğitim Programı
Tasarımı,” Elektrik, Elektronik, Bilgisayar
Mühendislik Eğitimi 1. Ulusal Sempozyumu Bildiriler Kitabı, 30 Nisan—2 Mayıs
Ankara, pp. 22—23, 2003
1999
·
Dursunkaya, Z., “Mühendislik
Programlarının Akreditasyonunda Yeni Yaklaşımlar,” TMMOB Mühendislik Mimarlik
Egitimi Sempozyumu Bildiriler Kitabı, 22—24 Ekim, pp. 200-205, 1999
Other
1974
·
Dursunkaya, Z., “Bilimsel Araştırma Nedir, Nasıl Yapılır?”,
Trakya’da Yeşilyurt, 5456—5459 Nisan—Mayıs 1974